-
ASTM D2570 Simulated Service Corrosion Tester
KN-2570 Simulated Service Corrosion Tester conforms to ASTM D2570 Standard Test Method for Simulated Service Corrosion Testing of Engine Coolants. An engine coolant is circulated for 1064h at 88℃ (190℉) in a flow loop consisting of a metal reservoir, an automotive coolant pump, an automotive radiator, and the connecting rubber hoses. Test specimens representative of engine cooling system metals are mounted inside the reservoir, which simulates an engine cylinder block. At the end of the test period, the corrosion-inhibiting properties of the coolant are determined by measuring the mass losses of the test specimens and by visual examination of the interior surfaces of the components.
Send Email Details -
ASTM D1287 PH Meter
KN-1287 PH Meter conforms to ASTM D1287 Standard Test Method for pH of Engine Coolants and Antirusts and ASTM D1121 Standard Test Method for Reserve Alkalinity of Engine Coolants and Antirusts. pH is a measure of the hydrogen ion concentration and indicates whether an engine coolant, or a solution of these compounds is acidic, alkaline, or neutral. The pH range includes values from 0 to 14. Values from 0 to 7 represent the acidic half of the scale. Values from 7 to 14 represent the alkaline or b
Send Email Details -
ASTM D4059 GC for PCBs in Insulating Liquids
KN-4059 GC for PCBs in Insulating Liquids conforms to ASTM D4059 Standard Test Method for Analysis of Polychlorinated Biphenyls in Insulating Liquids by Gas Chromatography. This test method describes a quantitative determination of the concentration of polychlorinated biphenyls (PCBs) in electrical insulating liquids by gas chromatography. It also applies to the determination of PCB present in mixtures known as askarels, used as electrical insulating liquids.
Send Email Details -
Automatic Penetration Tester
Automatic Penetration tester is used for not only evaluating the consistency of lubricating greases and wax ,but also evaluate the needle penetration for bitumen products.
Send Email Details -
ASTM D1120 Boiling Point Of Engine Coolants
The equilibrium boiling point indicates the temperature at which the sample will start to boil in a cooling system under equilibrium conditions at atmospheric pressure.
Send Email Details -
ASTM D566 Dropping Point Of Lubricating Grease
the dropping point is the temperature at which the grease passes from a semisolid to a liquid state under the conditions of test.
Send Email Details -
ASTM D6560 Apparatus for Paraffin, Resins and Asphaltenes Contents in Crude Oil
KN-6560 Apparatus for Paraffin, Resins and Asphaltenes Contents in Crude Oil in Crude Petroleum and Petroleum Products conforms to ASTM D6560 Standard Test Method for Determination of Asphaltenes (Heptane Insolubles) in Crude Petroleum and Petroleum Products and SY/T 7550 Determination of Paraffin, Resins and Asphaltenes Contents in Crude Oil. Asphaltenes are the organic molecules of highest molecular mass and carbon-hydrogen ratio normally occurring in crude petroleum and petroleum products containing residual material. They may give problems during storage and handling if the suspension of asphaltene molecules is disturbed through excess stress or incompatibility.
Send Email Details -
ASTM D7843 Membrane Patch Colorimetry
KN-7843 Membrane Patch Colorimetry conforms to ASTM D7843 Standard Test Method for Measurement of Lubricant Generated Insoluble Color Bodies in In-Service Turbine Oils using Membrane Patch Colorimetry. Insoluble deposits are extracted from an in-service turbine oil sample using a 47mm, 0.45μm membrane nitrocellulose patch. The color of the patch is then analyzed using a spectrophotometer and the results are reported as a △E value in the CIELAB scale.
Send Email Details
